FS Tool Series 527
FS Tool Carbide Tipped Saw Blade: Conic Scoring Saw Blades

Design:
• Tooth configuration: Conical ATB
• Cutting material: TC XL4000
• Expansion slots: CU plugged

Application:
• For pre-scoring in plastic laminated sheets
• On panel sizing saws with pre-scoring units
FS Tool Series 528
FS Tool Carbide Tipped Saw Blade: Split Scoring Saw Blades, Flat Top

Design
• Tooth configuration: Flat Top
• Cutting material: TC
• Two piece unit adjustable to the kerf of the main saw blade with the use of shims

Application
• For pre-scoring in plastic laminated sheets
• On table saws, sliding table saws and panel sizing saws with controllable pre-scoring units
FS Tool Series 529
FS Tool Carbide Tipped Saw Blade: Left Hand Scoring Saw Blades

Design:
• Tooth configuration: Unilaterally right
• Cutting material: TC
• Expansion slots: CU plugged

Application:
• For pre-scoring in solid wood, veneered and plastic laminated sheets
• On single or double end tenoners with pre-scoring units, in combination with hogging units
FS Tool Series 530
FS Tool Carbide Tipped Saw Blade: Right Hand Scoring Saw Blades

Design:
• Tooth configuration: Unilaterally left
• Cutting material: TC
• Expansion slots: CU plugged

Application:
• For pre-scoring in solid wood, veneered and plastic laminated sheets
• On single or double end tenoners with pre-scoring units, in combination with hogging units
FS Tool Series 531
FS Tool Carbide Tipped Saw Blade: Flat Top Scoring Saw Blades, Flat Top

Design:
• Tooth configuration: Flat Top
• Cutting material: TC
• Expansion slots: CU plugged

Application:
• For pre-scoring in plastic laminated sheets
• On single or double end tenoners with pre-scoring units, in combination with hogging units
FS Tool Series 560
FS Tool Carbide Tipped Saw Blade: Edge Banding Saw Blades

Design:
• Tooth configuration: see chart below (tooth shape & hook angle)
• Cutting material: TC
• Expansion slots: CU plugged

Application:
• For trimming projecting edge bandings of solid wood, wood veneer and plastics
• On single and double-sided edge banding machines
FS Tool Series 1TL
FS Tool Carbide Tipped Saw Blade: Segmented Hogging Units

Design:
• Hogger body made of light alloy equipped with 4 or 6 segments and one saw blade, all TC tipped, repalceable and resharpenable
• Standrad chipping width 30 cm, wider chipping widths in multiples of 30cm can be acheived by adding mutilple elements which must be specifed when ordering

Application:
• For Chip free sizing of panel materails on double-ened tenoners and triming machines
FS Tool Series 1TL2
FS Tool Carbide Tipped Saw Blade: Hogging Units With Disposable Knifes

Design:
•High tensile strength steel body with soild carbide reversiable inserts.
• Inserts have 4 cutting edges with chip breaker.
• Chipping width available from 19.2mm and wider, in increments of 15mm

Application:
• For chip-free sizing of panel materials on double-ened tenoners and trimming machines
FS Tool Series 53DL
FS Tool Carbide Tipped Saw Blade: Standard Dado Sets

Design:
• Standard Set adjustable from 1/4'' to 13/16'' in 1/16'' increments.  Consists of two outside saw blades 1/8'' kerf, 1/4'' chipper; two 1/8'' chippers and one 1/16'' Chipper

Application:
• To Cut grooves and dados in soft and hardwoods, plywood and veneered panels
• Used on Table saws, sliding table saws, and single or double end tenoners
FS Tool Series 53DLS
FS Tool Carbide Tipped Saw Blade: Saftey Dado Sets Antikickback Design

Design:
• Standard Set adjustable from 1/4'' to 13/16'' in 1/16'' increments.  Consists of two outside saw blades 1/8'' kerf, 1/4'' chipper; two 1/8'' chippers and one 1/16'' Chipper

Application:
• To Cut grooves and dados in soft and hardwoods, plywood and veneered panels
• Used on Table saws, sliding table saws, and single or double end tenoners
FS Tool Series 54DL
FS Tool Carbide Tipped Saw Blade: Fine Dado Sets

Design:
• Standard Set consists of two outside saw blades 1/8'' kerf, one 1/4'' chipper; two 1/8'' chippers and one 1/16'' Chipper
• Hook Angle 0º

Application:
• To Cut grooves and dados in plastic laminated panels
• Groove widths adjustable from 1/4'' to 13/16'' maximum width in 1/16'' increments. Wider grooves can be obtained by adding spare chippers.
• Used on table saws, sliding table saws, and single or double end tenoners
FS Tool Series 5G
FS Tool Carbide Tipped Saw Blade: Grooving Saw Blades

Design:
• Tooth configuration: Flat top
• Cutting material: TC

Application:
• For cutting grooves in soild wood, plywood, veerned and plastic laminated panels
• ON table saws, sliding table saws, single or double end tenoners and CNC routers
FS Tool Series L01
FS Tool Carbide Tipped Saw Blade: Fine Cross Cut Saw Blades for Plastic

Design:
• Tooth configuration: TC2
• Cutting material: TC
• Expansion slots: CU plugged

Application:
• For fine sizing cuts in single or double laminated panels, plexiglass and solid surface materials such as Wilsonart® Gibraltar®, SSV®; Corian®; Surell®; Avonite®; Fountainhead®, etc.
• On table saws, sliding table saws, radial arm saws and vertical panel sizing saws
• “Non-Melt” saw blades see LNM series
FS Tool Series L02
FS Tool Carbide Tipped Saw Blade: Rip Saw Blades with Chip Limiters, Flat Top

Design:
• Tooth configuration: Flat Top
• Cutting material: TC
• Expansion slots: CU plugged
• Saw body with chip thickness limiters

Application:
• For ripping dry soft and hardwoods
• On table saws and sliding table saws
• Ideal for hand fed operations
FS Tool Series L03
FS Tool Carbide Tipped Saw Blade: Cross Cut Saw Blades

Design:
• Tooth configuration: ATB
• Cutting material: TC
• Expansion slots: CU plugged

Application:
• For cross cutting and ripping dry soft and hardwoods, plywood, masonite and raw MDF panels
• On table saws, sliding table saws and cut-off saws
FS Tool Series L03TK
FS Tool Carbide Tipped Saw Blade: Thin Kerf Cross Cut Saw Blades, ATB

Design:
• Tooth configuration: ATB
• Cutting material: TC
• Expansion slots: CU plugged

Application:
• For cross cutting and ripping dry soft and hardwoods, plywood and veneered plywoods
• Not recommended to cut stock over ¾” without the use of stabilizer flanges
FS Tool Series L04
FS Tool Carbide Tipped Saw Blade: Standard Cross Cut Saw Blades, ATB

Design:
• Tooth configuration: ATB
• Cutting material: TC
• Expansion slots: CU plugged

Application:
• For general cut-off and trimming of soft and hardwoods, plywood and composite panel materials, wood veneered (single sided), or (double sided) using a pre-scoring unit
• On table saws, sliding table saws and cut-off saws
FS Tool Series L05
FS Tool Carbide Tipped Saw Blade: Thin Kerf Saw Blades, TCG

Design:
• Tooth configuration: refer to chart below (grind)
• Cutting material: TC
• Expansion slots: CU plugged
• Very stable body minimizes run-out

Application:
• For fine cross cuts in veneered panels, expensive woods and sheets, thin plexiglass, masonite and plastics
• On table saws, sliding table saws and vertical panel sizing saws
FS Tool Series L06
FS Tool Carbide Tipped Saw Blade: Fine Cross Cut Saw Blades, ATB

Design:
• Tooth configuration: ATB
• Cutting material: TC
• Expansion slots: CU plugged

Application:
For fine cut-off and trimming of soft and hardwoods, plywood, wood veneered and plastic laminated panel materials
On table saws, sliding table saws and cut-off saws
FS Tool Series L07
FS Tool Carbide Tipped Saw Blade: Radial Arm Saw Blades, ATB

Design:
Tooth configuration: 4 ATB & 1 Raker
Cutting material: TC
Expansion slots: CU plugged
0° hook angle reduces the tendency of the blade grabbing the material

Application:
• For cross cutting and ripping dry soft and hardwoods
• On radial arm saws and other saws where the blade is above the work piece
FS Tool Series L09
FS Tool Carbide Tipped Saw Blade: Fine Cross Cut Saw Blades, TCG

Design:
• Tooth configuration: TCG
• Cutting material: TC
• Expansion slots: CU plugged

Application:
• For fine sizing cuts in single or double sided melamine panels, MDF, OSB and HDF panels
• On table saws, sliding table saws and vertical panel sizing saws
FS Tool Series L10
FS Tool Carbide Tipped Saw Blade: Fine Cross Cut Saw Blades, TCG

Design:
• Tooth configuration: TCG
• Cutting material: TC
• Expansion slots: CU plugged

Application:
• For fine sizing cuts in single or double sided melamine panels, MDF, OSB and HDF panels
• On table saws, sliding table saws and vertical panel sizing saws
FS Tool Series L12
FS Tool Carbide Tipped Saw Blade: Gang Rip Saw Blades with Chip Limiters, Flat Top

Design:
• Tooth configuration: Flat Top
• Cutting material: TC
• Expansion slots: CU plugged
• Saw body with chip thickness limiters

Application:
• For ripping dry soft and hardwoods
• On gang-rip saws
FS Tool Series L13
FS Tool Carbide Tipped Saw Blade: Gang Rip Saw Blades with 2 Rakers, Flat Top

Design:
• Tooth configuration: Flat Top
• Cutting material: TC
• Two tungsten carbide rakers

Application:
• For ripping soft and hardwoods, dry up to 15% wood moisture
• On gang-rip saws with one or two shafts
FS Tool Series L14
FS Tool Carbide Tipped Saw Blade: Gang Rip Saw Blades with 2+2 Rakers, Flat Top

Design:
• Tooth configuration: Flat top
• Cutting material: TC
• Two chip clearance rakers and two wiper slots

Application:
• For ripping soft and hardwoods, wet or frozen
• On single and gang-rip saws with one or two shafts
FS Tool Series L15
FS Tool Carbide Tipped Saw Blade: Thin Rim Saw Blades, ATB

Design:
• Tooth configuration: ATB
• Cutting material: TC
• Expansion slots: CU plugged
• Thin rimmed body (on left side) allows for thin kerf at teeth and stability during cutting operation

Application:
• For fine cross cuts in veneered panels, expensive woods and sheets, thin plexiglass, masonite and plastics
• On table saws and sliding table saws
FS Tool Series L16
FS Tool Carbide Tipped Saw Blade: Thin Rim Saw Blades, TC2

Design:
• Tooth configuration: TC2
• Cutting material: TC
• Expansion slots: CU plugged
• Thin rimmed body (on left side) allows for thin kerf at teeth and stability during cutting operation

Application:
• For thin cross cuts in acrylic sheets, thin plexiglass, masonite and plastics
• On table saws and sliding table saws
FS Tool Series L18
FS Tool Carbide Tipped Saw Blade: Heavy Duty Rip Saw Blades, Flat Top

Design:
• Tooth configuration: Flat Top
• Cutting material: TC
• Expansion slots: CU plugged

Application:
• For ripping dry soft and hardwoods
• On table saws or gang-rip saws with one or two shafts
FS Tool Series L19
FS Tool Carbide Tipped Saw Blade: Cross Cut Saw Blades, TCG

Design:
• Tooth configuration: TCG
• Cutting material: TC
• Expansion slots: CU plugged

Application:
For cross cutting and ripping soft and hardwoods, composite materials plastic laminated (single sided)
On table saws, sliding table saws and cut-off saws
FS Tool Series L1A
FS Tool Carbide Tipped Saw Blade: Saw Blades for Non-Ferrous Metals, TCG

Design:
• Tooth configuration: TCG
• Cutting material: TC
• Expansion slots: CU plugged

Application:
• For splitting and mitre jointing non-ferrous extrusions, sheets and light bars
• On mitre joint, splitting, trimming, double cross-cutting and sizing machines
• Material to be cut must be clamped firmly
• Use of spray lubrication recommended
FS Tool Series L1B
FS Tool Carbide Tipped Saw Blade: Saw Blades for Non-Ferrous Metals, TCG

Design:
• Tooth configuration: TCG
• Cutting material: TC
• Expansion slots: CU plugged

Application:
• For splitting and mitre jointing thin non-ferrous extrusions, thin sheets and light non-ferrous bars
• On mitre joint, splitting, trimming, double cross-cutting and sizing machines
• Material to be cut must be clamped firmly
• Use of spray lubrication recommended
FS Tool Series L1C
FS Tool Carbide Tipped Saw Blade: Standard Rip Saw Blades, Flat Top

Design:
• Tooth configuration: Flat Top
• Cutting material: TC
• Expansion slots: CU plugged

Application:
• For ripping dry soft and hardwoods
• On table saws or gang-rip saws with one or two shafts
FS Tool Series L21
FS Tool Carbide Tipped Saw Blade: Standard Rip Saw Blades, Flat Top

Design:
• Tooth configuration: Flat Top
• Cutting material: TC
• Expansion slots: CU plugged

Application:
• For ripping dry soft and hardwoods
• On table saws or gang-rip saws with one or two shafts
FS Tool Series L21TK
FS Tool Carbide Tipped Saw Blade: Thin Kerf Rip Saw Blades, Flat Top

Design:
• Tooth configuration: Flat Top
• Cutting material: TC
• Expansion slots: CU plugged

Application:
• For ripping dry soft and hardwoods
• On table saws or gang-rip saws
FS Tool Series L22
FS Tool Carbide Tipped Saw Blade: Glue Line Rip Saw Blades TCG

Design:
• Tooth configuration: TCG
• Cutting material: TC
• Expansion slots: CU plugged
 
Application:
• For glue line ripping dry soft and hardwoods
• Extra smooth cut for gluing applications
• On straight line rip saws, gang-rip saws and table saws
FS Tool Series L23
FS Tool Carbide Tipped Saw Blade: Standard Cross Cut Saw Blades, TCG

Design:
• Tooth configuration: TCG
• Cutting material: TC
• Expansion slots: CU plugged

Application:
• For general cut-off and trimming of plastic laminated materials (single sided), or (double sided) using a pre-scoring unit
• On table saws, sliding table saws and cut-off saws
FS Tool Series L2A
FS Tool Carbide Tipped Saw Blade: Glue Line Rip Saw Blades ATB

Design:
• Tooth configuration: ATB
• Cutting material: TC
• Expansion slots: CU plugged

Application:
• For glue line ripping dry soft and hardwoods
• Extra smooth cut for gluing applications
• On table saws
FS Tool Series L41
FS Tool Carbide Tipped Saw Blade: Hollow Face Saw Blades, TCH

Design:
Tooth configuration: TCH (face hollow-ground)
Cutting material: TC
Expansion slots: CU plugged

Application:
• For exceptionally smooth cuts (on both sides) in melamine and other laminated panels, without the need for pre-scoring
• On table saws, sliding table saws and vertical panel sizing saws
FS Tool Series L42
FS Tool Carbide Tipped Saw Blade: Hollow Face Saw Blades, Hollow Ground

Design:
• Tooth configuration: inverted “V” (face hollow-ground)
• Cutting material: TC
• Expansion slots: CU plugged

Application:
• For exceptionally smooth cuts (on both sides) in melamine and other laminated panels, without the need for pre-scoring
• For mitre cuts in wrapped styrene picture frames
• On table saws, sliding table saws, vertical panel sizing saws and mitre saws
FS Tool Series L4D
FS Tool Carbide Tipped Saw Blade: Double Cut Off Saw Blades, 3 Beveled One Side And 1 Beveled Opposite Side

Design:
• Tooth configuration: 3 beveled one side & 1 beveled opposite side. Supplied in pairs 1 LH & 1 RH (order separately)

Application:
• For fine cut-off and mitre cuts of soft and hardwoods, and trimming of plywood, wood veneered and plastic laminated panels (single sided), or (double sided) using a pre-scoring unit
• On double cut-off machines and single or double end tenoners
FS Tool Series L50
FS Tool Carbide Tipped Saw Blade: XL4000 Panel Sizing Saw Blades, ATB

Design:
• Tooth configuration: ATB
• Cutting material: TC XL4000
• Expansion slots: Cu plugged

Application:
• For sizing cuts in veneered particle board, hard fiberboard, raw MDF panels and high-density plywood in single sheets and stacks
• On panel sizing saws (Beam Saws)
FS Tool Series L52
FS Tool Carbide Tipped Saw Blade: XL4000 Panel Sizing Saw Blades, TCG

Design:
• Tooth configuration: TCG
• Cutting material: TC XL4000
• Expansion slots: Cu plugged

Application:
• For sizing cuts in plastic laminated panels and plywood in sheets and stacks
• On panel sizing saws (Beam Saws)
FS Tool Series L55
FS Tool Carbide Tipped Saw Blade: Combination Saw Blades, ATB

Design:
• Tooth configuration: 4 ATB & 1 Raker
• Cutting material: TC
• Four ATB teeth and one raker with deep gullet allow for deeper cuts and improved chip-flow

Application:
• For cross cutting and ripping soft and hardwoods, plywood and particleboard
• On table saws, sliding table saws and cut-off saws
FS Tool Series L6D
FS Tool Carbide Tipped Saw Blade: Double Cut Off Saw Blades, 3 Beveled One Side And 1 Beveled Opposite Side

Design:
• Tooth configuration: 3 beveled one side & 1 beveled opposite side. Supplied in pairs 1 LH & 1 RH (order separately)

Application:
• For fine cut-off and mitre cuts of soft and hardwoods, and trimming of plywood, wood veneered and plastic laminated panels (single sided), or (double sided) using a pre-scoring unit
• On double cut-off machines and single or double end tenoners
FS Tool Series LHCF
FS Tool Carbide Tipped Saw Blade: Chip-Free Melamine Trim Blades

Design:
• Tooth configuration: High ATB (30 degrees)
• Cutting material: TC
• Expansion slots: Laser, Self plug

Application:
• For chip free sizing cuts (on both sides) in melamine and wood veneered panels, without the need for pre-scoring
• For fine cross-cuts in solid woods
• On table saws, sliding table saws, vertical panel sizing saws and cut-off saws
FS Tool Series LHCP
FS Tool Carbide Tipped Saw Blade: Combination/Planer Saw Blades

Design:
• Tooth configuration: 4 ATB & 1 Raker
• Cutting material: TC
• Four ATB teeth and one raker with deep gullet allow for deeper cuts and improved chip flow

Application:
• For cross cutting and ripping dry soft and hardwoods, plywood and particleboard
• On portable machines and Table saws
FS Tool Series LHCS
FS Tool Carbide Tipped Saw Blade: Saw Blades For Cordless Machines

Design:
• Cutting material: TC
• Expansion slots: laser, self plug

Application:
• For cross cutting solid wood, veneered and plastic laminated sheets
• On portable machines
FS Tool Series LHFC
FS Tool Carbide Tipped Saw Blade: Fine Cross Cut Saw Blades

Design:
• Cutting material: TC
• Expansion slots: laser, self plug

Application:
• For fine cut-off and trimming of solid woods, plywood, wood veneered and plastic laminated panel materials
• On portable machines and table saws
FS Tool Series LHGA
FS Tool Carbide Tipped Saw Blade: General Application Saw Blades

Design:
• Cutting material: TC
• Expansion slots: laser, self plug

Application:
• For ripping and general cross cutting of dry solid woods
• On portable machines and table saws
FS Tool Series LHMJ
FS Tool Carbide Tipped Saw Blade: Mitre Joint Saw Blades

Design:
• Tooth configuration: 4 ATB & 1 Raker
• Cutting material: TC
• Expansion slots: laser, self plug

Application:
• For mitre joint cuts in soft and hardwood picture frames and furniture mouldings
• On cut-off mitre machines, compound mitre machines, radial arm saws, and table saws
FS Tool Series LHRS
FS Tool Carbide Tipped Saw Blade: Demolition-Firemans Saw Blades

Design:
• Tooth configuration: TCGN
• Cutting material: TC
• Modified grind and 15 degrees negative hook reduces the possibility of tooth damage

Application:
• For rough cutting applications
• On gasoline powered machines
FS Tool Series LHSC
FS Tool Carbide Tipped Saw Blade: Mitre Joint Saw Blades, ATB

Design:
• Tooth configuration: 4 ATB & 1 Raker
• Cutting material: TC
• Expansion slots: CU plugged

Application:
• For mitre joint cuts in soft and hardwoods, painted mouldings, gesso and other high-gloss and pre-finished picture frames and furniture mouldings as well as P.V.C. substrates
• For aluminum cuts see L1A, L1B, L1C series page E36, E37
• On single or double cut-off mitre machines and radial arm saws
FS Tool Series LM4
FS Tool Carbide Tipped Saw Blade: Mitre Joint Saw Blades, ATB

Design:
• Tooth configuration: 4 ATB & 1 Raker
• Cutting material: TC
• Expansion slots: CU plugged

Application:
• For mitre joint cuts in soft and hardwoods, painted mouldings, gesso and other high-gloss and pre-finished picture frames and furniture mouldings as well as P.V.C. substrates
• For aluminum cuts see L1A, L1B, L1C series page E36, E37
• On single or double cut-off mitre machines and radial arm saws
FS Tool Series LM6
FS Tool Carbide Tipped Saw Blade: Mitre Joint Saw Blades, ATB

Design:
• Tooth configuration: 4 ATB & 1 Raker
• Cutting material: TC
• Expansion slots: CU plugged

Application:
• For mitre joint cuts in soft and hardwoods, painted mouldings, gesso and other high-gloss and pre-finished picture frames and furniture mouldings as well as P.V.C. substrates
• For aluminum cuts see L1A, L1B, L1C series page E36, E37
• On single or double cut-off mitre machines and radial arm saws
FS Tool Series LM6-30°
FS Tool Carbide Tipped Saw Blade: Chip-Free Melamine Trim Blades, High ATB (30°)

Design:
• Tooth configuration: High ATB (30°)
• Cutting material: TC
• Expansion slots: CU plugged

Application:
• For chip-free sizing cuts (on both sides) in melamine and wood veneered panels, without the need for pre-scoring
• For fine cross cuts in solid woods
• On table saws, sliding table saws, vertical panel sizing saws and cut-off saws
FS Tool Series LNM
FS Tool Carbide Tipped Saw Blade: Non-Melt Saw Blades, TC2

Design:
• Tooth configuration: TC2
• Tooth geometry specifically designed to minimize “melting” of material
• Cutting material: TC
• Expansion slots: CU plugged

Application:
• For “non-melt” fine cuts in acrylic sheets, selrins, ABS (cycolac), Styrenes and PVC
• On table saws, sliding table saws and vertical panel sizing saws
FS Tool Series S03
FS Tool Carbide Tipped Saw Blade: XL4000 Cross Cut Saw Blades, ATB

Design:
• Tooth configuration: ATB
• Cutting material: TC XL4000
• Expansion slots: CU plugged

Application:
• For cross cutting and ripping dry soft and hardwoods, plywood, masonite and raw MDF panels
• On table saws, sliding table saws and cut-off saws
FS Tool Series S04
FS Tool Carbide Tipped Saw Blade: XL4000 Fine Cross Cut Saw Blades, ATB

Design:
• Tooth configuration: ATB
• Cutting material: TC XL4000
• Expansion slots: CU plugged

Application:
• For fine cut-off and trimming of soft and hardwoods, plywood, wood veneered and plastic laminated panel materials
• On table saws, sliding table saws and cut-off saws
FS Tool Series S06
FS Tool Carbide Tipped Saw Blade: XL4000 Fine Cross Cut Saw Blades, ATB

Design:
• Tooth configuration: ATB
• Cutting material: TC XL4000
• Expansion slots: CU plugged

Application:
• For fine cut-off and trimming of soft and hardwoods, plywood, wood veneered and plastic laminated panel materials
• On table saws, sliding table saws and cut-off saws
FS Tool Series S07
FS Tool Carbide Tipped Saw Blade: XL4000 Radial Arm Saw Blades, ATB

Design:
• Tooth configuration: 4 ATB & 1 Raker
• Cutting material: TC XL4000
• Expansion slots: CU plugged
• 0° hook angle reduces the tendency of the blade grabbing the material

Application:
• For cross cutting and ripping dry soft and hardwoods
• On radial arm saws and other saws where the blade is above the work piece
FS Tool Series S09
FS Tool Carbide Tipped Saw Blade: XL4000 Cross Cut Saw Blades, ATB

Design:
• Tooth configuration: ATB
• Cutting material: TC XL4000
• Expansion slots: CU plugged

Application:
• For cross cutting and ripping dry soft and hardwoods, plywood, masonite and raw MDF panels
• On table saws, sliding table saws and cut-off saws
FS Tool Series S10
FS Tool Carbide Tipped Saw Blade: XL4000 Fine Cross Cut Saw Blades, TCG

Design:
• Tooth configuration:TCG
• Cutting material: TC XL4000
• Expansion slots: CU plugged

Application:
• For fine sizing cuts in single or double sided melamine panels, MDF, OSB and HDF panels
• On table saws, sliding table saw and vertical panel sizing saws
FS Tool Series S19
FS Tool Carbide Tipped Saw Blade:XL4000 Cross Cut Saw Blades, TCG

Design:
• Tooth configuration: TCG
• Cutting material: TC XL4000
• Expansion slots: CU plugged

Application:
• For cross cutting and ripping dry soft and hardwoods
• On table saws, sliding table saws and cut-off saws
FS Tool Series S21
FS Tool Carbide Tipped Saw Blade: XL4000 Heavy Duty Rip Saw Blades, Flat Top

Design:
• Tooth configuration: Flat Top
• Cutting material: TC XL4000
• Expansion slots: CU plugged

Application:
• For ripping dry soft and hardwoods
• On table saws or gang rip saws with one or two shafts
FS Tool Series S22
FS Tool Carbide Tipped Saw Blade: XL4000 Glue Line Rip Saw Blades, TCG

Design:
• Tooth configuration: TCG
• Cutting material: TC XL4000
• Expansion slots: CU plugged

Application:
• For glue line ripping dry soft and hardwoods
• Extra smooth cut for gluing applications
• On straight line rip saws, gang rip saws and table saw
FS Tool Series S23
FS Tool Carbide Tipped Saw Blade: XL4000 Standard Cross Cut Saw Blades, TCG

Design:
• Tooth configuration: TCG
• Cutting material: TC XL4000
• Expansion slots: CU plugged

Application:
• For general cut-off and trimming of plastic laminated materials (single sided), or (double sided) using a pre-scoring unit
• On table saws, sliding table saws and cut-off saws
FS Tool Series S4D
FS Tool Carbide Tipped Saw Blade: XL4000 Double Cut Off Saw Blades, 3 Beveled One Side And 1 Beveled Opposite Side

Design:
• Tooth configuration: 3 beveled one side and 1 beveled opposite side. Supplied in pairs 1 LH & 1 RH (order separately)

Application:
• For fine cut-off and mitre cuts of soft and hardwoods, and trimming of plywood, wood veneered and plastic laminated panels (single sided), or (double sided) using a pre-scoring unit
• On double cut-off machines and single or double end tenoners
FS Tool Series S55
FS Tool Carbide Tipped Saw Blade: XL4000 Combination/Planer Saw Blades, ATB

Design:
• Tooth configuration: 4 ATB & Raker
• Cutting material: TC XL4000
• Four ATB teeth and one raker with deep gullet allow for deeper cuts and improved chip-flow

Application:
• For cross cutting and ripping dry soft and hardwoods, plywood and particleboard
• On table saws, sliding table saws and cut-off saws
FS Tool Series S6D
FS Tool Carbide Tipped Saw Blade: XL4000 Double Cut Off Saw Blades, 3 Beveled One Side And 1 Beveled Opposite Side

Design:
• Tooth configuration: 3 beveled one side and 1 beveled opposite side. Supplied in pairs 1 LH & 1 RH (order separately)

Application:
• For fine cut-off and mitre cuts of soft and hardwoods, and trimming of plywood, wood veneered and plastic laminated panels (single sided), or (double sided) using a pre-scoring unit
• On double cut-off machines and single or double end tenoners
FS Tool Series SM6
FS Tool Carbide Tipped Saw Blade: XL4000 Mitre Joint Saw Blades, ATB

Design:
• Tooth configuration: 4 ATB & 1 Raker
• Cutting material: TC XL4000
• Expansion slots: CU plugged

Application:
• For mitre joint cuts in soft and hardwoods, painted mouldings, gesso and other high-gloss and pre-finished picture frames and furniture mouldings as well as PVC substrates
• For aluminum cuts see L1A, L1B, L1C, series
• On single side or double cut-off mitre machines and radial arm saws
FS Tool Series SM6-30°
FS Tool Carbide Tipped Saw Blade: XL4000 Chip-Free Melamine Trim Blades, High ATB (30°)

Design:
• Tooth configuration: High ATB (30°)
• Cutting material: TC XL4000
• Expansion slots: CU plugged

Application:
• For chip-free sizing cuts (on both sides) in melamine and wood veneered panels, without the need for pre-scoring
• For fine cross cuts in solid woods
• On table saws, sliding table saws, vertical panel sizing saws and cut-off saws
FS Tool Series SS1
FS Tool Carbide Tipped Saw Blade: XL4000 Solid Surface Saw Blades, TC2

Design:
• Tooth configuration: TC2
• Cutting material: TC XL4000
• Expansion slots: CU plugged

Application:
• For fine sizing cuts in single or double laminated panels, plexiglass and solid surface materials such as Wilsonart® Gibraltar®, SSV®; Corian®; Surell®; Avonite®; Fountainhead®, etc.
• On table saws, sliding table saws, radial arm saws and vertical panel sizing saws